Dunmore PA Commercial Refrigeration

Commercial Coffee Machine Repair Service. Upon identifying limescale buildup, I performed a thorough descaling process, ensuring consistent coffee brewing and meeting the client’s business demands.

Commercial Pizza Oven Installation: The client wanted to expand their offerings with a new pizza oven. I installed the unit, connected the gas and electrical lines, and fine-tuned the temperature controls. Testing confirmed consistent baking quality, and I provided guidance to the client on maintaining the oven for peak performance.

Commercial Kitchen Equipment Repair Service: The client noticed their refrigeration unit was not maintaining temperature due to cold air escaping. I found that the door seal was worn and cracked. I replaced the seal, ensuring the unit could maintain optimal cooling without wasting energy.

Commercial Kitchen Equipment Repair Service: The client’s hot dog roller was squeaking and moving unevenly. After inspection, I found the roller bearings were worn. I replaced the bearings and lubricated the mechanism, ensuring smooth and quiet operation.

Commercial Kitchen Maintenance Service: Replaced water filtration systems that were nearing the end of their lifespan, ensuring continued water purity and safety.

Commercial Kitchen Appliance Repair: Replaced worn-out O-rings in an ice cream machine to prevent leaks.

Commercial Kitchen Equipment Repair: Upon arrival, I found that the client’s conveyor belt in the warewashing machine was misaligned. I realigned the belt, ensuring smooth and efficient dishwashing operations.

examined Heat Lamp unit, breaker shut off. Removed power switch panel and found 20a household On/Off switch and all wiring inside conduit box burnt up. Best course of action would be to replace unit as age is unknown, no model or serial number on unit. Looks to be a crescor but no other information. Unit is 60" 120V. If replacement is not an option, unit will need incoming power wire cut back and stripped, 20a Switch replaced, Wire going to elements from switch replaced. Wires look to be 10 gauge. Power to unit is currently off and should not be switched back on. Closing out this work order.

Found Gas Fryer first vat on left would not cycle on, computer blank - removed panels, have 12 volts and 24 volts at interface board unplugged computer wire harness and put Bach in computer lite and cycled on unit part number on computer (controller 1086212 item number 1085777 ) Unit came up to temp - will get price on computer controller Note: controller is no longer available, called and left message for customer. Closing out work order.

Middle oven pilot on, no gas coming through for burner, safety button stuck and always letting pilot gas through. Replaced safety and thermocouple, tested.

Examined Hot Well unit. Found 2=212081=THERMOSTAT,ELECTRIC KA604 #KA6 - 5=223590= knob Customer requests 5 knobs and two thermostat knob rods are broken so whole thermostat needs replacement. 4-3-19 Replaced all five knobs and 4th and 5th thermostat from right. Tested okay.

Found electric Fryer unit on and working, customer advised that unit shut off and would no cycle back and controller was blank - switched control to unit to left. If problems goes to left fryer will need control, if problems stay in right vat, maybe power/relay board.

Examined Dishwasher unit rinse temps are good wash temp is good pressure gauge not working on water line rinse solenoid opening hot water getting by during wash and ran several cycles and none were the same on normal wash times from 48 sec to almost 4 mins. unit leaking were rinse line goes thru top will need to tighten. 3/11/19 Replaced water solenoid valve and pressure gauge tightened leaky fitting on rinse feed, replaced timer filled unit brought to temp ran several cycles all around 45 wash and 15 rinse all okay

Found Warming Cabinet units thermostat is bad, one side is a Robert Shaw thermostat (1) 5000-814, need knob to match thermostat. Unit is aTraulsen model number n/a 1-25-19 Replaced thermostat and knob, tested drawing 5 amps unit working, finished assembly all okay.

Examined Grill unit, found far left thermostat stem mangled. Straightened out and tested. Found valve seized and knob also ruined from trying to turn on seized valve. Customer stated unit cycles off and goes into a bypass but recently stopped. GS style thermostats don't have a bypass. Spoke with Anthony. advised we will return with surface tester to make sure other thermostats are functioning properly. 1-16-19 Removed and replaced far left thermostat. Checked all 4 thermostats for calibration, all 4 thermostats within 10 degree of each other. Good to go, will part sale knob