Lewisburg PA Commercial Refrigeration

Arrived on, 8-17-23- Sam S-Checked freezer, neither of the evap fans are running. Not getting power to either fan. Ordered digital controller and both door switches that were sticking. Freed up switches for the time being. Returned on, 8-29-23 Sam S-Installed new controller and door switches. Confirmed fans run now. Checked cooling and defrost all ok.

Arrived at location on 1/27/22 - Checked over unit. Found blower runs rough. Customer is going to take care of it at a later time. Watched unit run found some loose wires causing unit to lose 24v. Repaired wires and ran unit. Found unit runs at this time.

Commercial deep fryer repair service on Frymaster gas fryer.

Checked over Top Oven unit, found gas valve sticks open. replaced with truck stock and tested, okay at this time. **No Travel Charges per Service Manager**

Frymaster service repair on gas fryer. Check pilot staying lit and voltage. Clean and perform maintenance.

Turned Oven unit on and let heat found temp control would adjust to random temperatures. Will order new temp board, probe and knob and return to replace. 6/12/19 Removed the faulty stat, probe and knob then installed new. Then programmed the unit and checked calibration to adjust as needed. The unit is maintaining temperature fine but both cooling fans are supplied with 120v but are not working and need replaced. We will need to order and return to replace. 7/5/19 Removed failed cooling fans, replaced fans, energized and checked operation unit operating normally at this time.

I lit the Gas Fryer pilot and fired the unit up to check operation. The unit shut off at set point and the pilot stayed lit. I checked while the unit was running and I had a 170mv drop across the stat. I took the connections apart and cleaned everything up and that took care of the large voltage drop. The gas valve was on the edge of not having enough voltage to stay open. The unit is working fine at this time. **Travel Charges Billed on wo# 180591**

Found noise coming from convection Oven fan motor. Found burned wire on motor repaired wire. Will need new motor. 4/30/19 Pulled unit apart and removed the faulty motor then installed new. I checked operation and the unit is working fine at this time..

checked Oven operation and the fan wouldn't come on in low but would try in high (No capacitor present). The motor and switch need replaced and we can try to get blower wheel off and re-use. The customer would like a quote to install the new parts and one for a completely new oven. 12-28-18 Removed back panel and attempted to remove fan blade had to cut shaft. Installed and wired in new motor and installed fan blade. Installed new speed switch. Turned unit on checked operation of motor and switch found okay. Unit is operating at this time.

Checked over Combi Oven unit, found will not ignite. Found issue due to bad hot surface ignitor and flame sensor. Will replace both. 8-10-18 Found unit in operation, let customer finish with it. Replaced hot surface ignitor and flame sensor, turned unit on. Unit heated normally. Unit is running okay at this time.

The unit was at 45 degrees and the staff said they had adjusted the stat multiple times because it was above 50 degrees. I pulled the unit out and removed the back and the condenser was plugged. I brushed and cleaned it with dirt blaster They ran the unit and adjusted it multiple times to get it to shut off at 34 degrees. I told the staff to let it run for a day and check temp before putting product back in.

Found power switch on Oven unit not locking into on position. Removed switch and cleaned but intermittently fails to lock on. Will need switch ordered and replaced. 4-13-18 Removed failed power switch. Installed and wired new switch. Energized and checked operations. **Travel Charges Billed on WO# 154219**

Found SBR Oven Range door spring retainer bracket loose. Tightened bracket and reassembled door spring assembly. Door operating normally at this time.

Found reach-In Freezer unit with temp. control set to coldest setting. Unit was freezing coil and not defrosting properly causing high temp. Set temp. control to correct position ( 4 on dial), unit cycles normally at 0°F.

Found unit off. Griddle burner valves need replaced, not lighting properly. Unable to measure gas pressure but unit may need regulator. Oven valve also needs replaced. Will order and return. 3/30/17 replaced regulator and locally purchased nipples. Unit needs t-stat, flange, and knob. Will order and return. 4/7/17 found unit off. Removed center t-stat, found the tee and supply lines both need to be removed behind manifold so they t-stat would fit. Installed new, turned on, calibrated, cycling at 350*

Found unit not able to pump oil. Motor burned up due to overheat. Replaced filter pump and motor, ran, unit okay at this time.

found unit off at breaker, checked over unit, found thermostat set high and boiled booster. Adjusted thermostat to get even 180*F during rinse, will need thermostat and thermometer due to rust build up on bulb to thermometer not reading right, Per Terry over the phone, QWP (expedited freight) part, unit is down, thermostat is turned all the way down and continues to heat. 2-13-17 found unit off, replaced thermometer, found thermostat to be incorrect, will obtain correct one and return to replace along with power switch. 2/15/17 found unit off. Removed faulty booster t-stat and rocker switch, installed new Ran, adjusted booster t-stat to maintain proper rinse temp at 182* and wash temp 155*. Unit ok at this time.

I found unit (BEC toaster) off, turned on and conveyor worked but top and bottom would not heat. Spoke to rep at Belleco, bypassed reset switch, found top of unit heated. Spoke to service manager, he said to leave switch bypassed, will obtain new bottom heat tubes and switch and return to replace. I found unit on. Turned off, unplugged, installed new hi limit and 2 element tubes that were damaged. Unit okay at this time.

Wells Electric Oven Tech - found unit on but not heating. Found 204v to coil of contactor. Contactor not pulling in. Replaced with contactor from truck. Applied power, contactor pulled in. Unit heated, each element pulling 12 amps. Unit is ready to use.

FryMaster Electric Fryer Service Performed 7/14/15 Replaced bad fuse, replaced AIF board for vats #4 and #5

FryMaster Electric Fryer Service Performed 7/8/15 Filtered each vat using auto filtration, recorded error logs